Name: Meteor85 Brushless Whoop Quadcopter (2S)
SKU: 928034

The name Beta85 Pro 2 and Meteor85 are both for this drone. We would like to use the name Meteor85 progressively.

Beta85 Pro 2, a new approach to the 2S micro formula which optimizes weight. This provides a smoother flight experience that's easier to control at high speed and easier on battery life as well. You have plenty of power to use both indoor and outdoor spaces as a small-scale acro playground. The weight savings also provide a handling advantage on the racecourse, allowing tighter turns and making it easier to hit gates.

Inspired by & 's ShutterBug85, this build is dramatically reduced weight and optimized the flight experience, and the acro performance is really awesome. Beta85 Pro 2 is the best combination for pilots, you do not need to assemble it by hand but also get more power on punch for acro mode.

ELRS 2.4G Version

ExpressLRS is the most popular radio link in 2021. ExpressLRS aims to achieve the best possible link performance in both speeds, latency, and range. Know more about the ExpressLRS project on or join the discussion in the .

In order to meet the FPV polit's requirement for ELRS whoop drones, the ELRS 2.4G version Beta85 Pro 2 is here. Comparison with the SPI Frsky version, what is the upgrade point on the new ELRS 2.4G version drone?

The FC board is the , which integrates BLHeli_S 12A ESC and SPI ExpressLRS 2.4G receiver.
could provide highest 350mW output power. So both the radio link and FPV video link could be long enough.
It comes with camera and .

Bullet Points

Beta85 Pro 2 starts a new era of 2S whoop, which could fly real acro, like a larger quad, but is still safe enough, light enough, and durable enough to fly anywhere, especially suitable for racing.
With the high-performance STM32F411CEU6 processor FC boards and tuned betaflight_4.2.0_STM32F411, everyone could fly the Beta85 Pro 2 drone like a racing pro.
With durable and light enough frame. A total weight of 42g gives pilots a good balance of weight and a nice punch on a 2S battery.
Whole drone no soldering or tinkering necessary. Customized lightest 1103 11000KV motors with cable connectors. Just plug and play.
300mAh 2S high rate battery is recommended by default. The drone comes with an XT30 cable, convenient for installing the 2S battery. But pilots could also use their whoop batteries with a replaced power cable. Optional and affordable.

Specifications

Weight: 42g (without battery)
FC: /
Motors:
Props:
Camera: / Caddx Ant Camera (only for ELRS 2.4G version)
Frame:
Canopy: / 2022
Receiver Option: SPI Frsky FCC / / / ELRS 2.4G
VTX: Integrates 25mW VTX / (only for ELRS 2.4G version)
Battery:
Flight time: 3 minutes with 300mAh 2S battery

Caution: Please correctly connect the battery's positive and negative terminals to prevent drone damage.

Props out

The Beta85 Pro 2 drone comes with "props out" in default. Why do we need "props out" direction?

Default Betaflight props direction, quadcopter dips, and "washes out" in hard corners. With reversed props or "props out", no more dipping even in hardest cornering.

Related Detail

For more video about these 2S Whoop drones, please check here:

Have any questions about the 2S Whoop drone, please join our group on Facebook:

FAQ

1. Does this drone have a current sensor?

This drone does NOT have a real current sensor. We use the virtual current meter in Betaflight. When properly calibrated, it can be accurate enough to be useful. Here is the pre-calibrated value out of the box.

set current_meter = VIRTUAL
set ibatv_scale = 90
set ibatv_offset = 29

2. Binding procedure of F4 2S AIO (SPI Frsky RX) is given on our .

3. Cli Dump for different versions of the 2S Whoop are provided on our .

4. The camera tilt angle is 30 degrees by default.

5. If you are using EU-LBT firmware radio controller, you might find that you can't bind successfully to this SPI Frsky receiver. Here are the we provide for you.

6. If your Beta85 Pro 2 (SPI Frsky Receiver) shuts down and falls down randomly, please read on the support page.

7. How to set up smart audio VTX control? ( gives you the most straightforward explanation)

8. Now the default F4 1S 12A FC (ELRS 2.4G) firmware for the Meteor85 ELRS version is updated to Betaflight V4.3.0 RC6 which, supports ELRS V2.0. For the ERLS V1.0 version, if you need to update it for supporting ERLS V2.0, please refer to the link below.

(Betaflight_4.3.0_Official_Version_Meteor85_ELRS.hex)

(betaflight_4.3.0_BETAFPVF4SX1280.hex)

(BTFL_cli_Meteor85-ELRS 2.0_DIFF_Official_Version.txt)